MINI V-MAX "RADAR V-LINE" ULTRASONIC HIFU + RF [RADIO FREQUENCY] DEVICE
RECHARGEABLE POWER: 100-240V
The Ultimate Skin Tightening & Face Lifting Device for the perfect "V-Shaped" Contour
This device is soon to be your new best friend.
The Mini V-Max "Radar V-Line" is a compact and portable face-lifting & contour 'carving' device which combines the anti-aging technology of Mechanical Wave/ RF (Radio Frequency) with Ultrasonic HIFU.
- HIFU was approved by the Food and Drug Administration (FDA) in 2009 for brow lifts. The device was also cleared by the FDA in 2014 to improve lines and wrinkles of the upper chest and neckline (decolletage).
- Provides supreme anti-aging face lifting
- Encourages Product (Active Ingredient) "Lead-In" : for extreme nutrient absorption.
- Promotes the regeneration of the fascia layer and increases collagen production in the skin
- Superior Tightening and V-Line Contouring
Through the delivery of advanced thermal HIFU [High Intensity Focused Ultrasound], the deep tissue layers of the skin are targeted, thermally heated and fully penetrated. The SMAS [Superficial Muscular Aponeurotic System] is the layer of tissue deep within the skin and the subcutaneous tissue. The SMAS is by far one of the most important support structures for the face. Advanced thermal HIFU provides a specialized manipulation to this anatomic structure; which enhances muscular definition and produces obvious changes to the appearance of the skin and face.
- Mini V-Max reaches 3.0mm-4.5mm beneath the skin's surface; fully penetrating (much deeper than other lasers) into the layer of muscles underneath the facia muscles.
- The facia is a band or sheet of connective tissue, primarily collagen, beneath the skin that attaches, stabilizes, encloses, and separates muscles and other internal organs.
Through a process called Phonophoresis, the application of a continuous pulse creates a series of compression waves. These waves force the active ingredients [skin actives] from your favorite treatment products- deep into the dermis layer. This process occurs when a compression wave causes a bubble at the surface of the skin to collapse, forming what is called an acoustic microjet. This microjet creates a tiny tunnel that acts as a gateway which allows full access into the skin.
- The combined effects prove to be highly beneficial and improve the overall health and appearance of the skin.
- Routine treatments provide visible results equivalent to that of high-end facials or professional cosmetic procedures.
When the body experiences exercise, the heightened stimulation to the body causes the muscles to contract and release. Mini V-Max administers specialized wave frequencies deep into the skin that essentially mimic exercise and elicit a similar response from the subcutaneous facial muscles. As the muscles begin to contract and release, the skin's cells are prompted to increase production of collagen, elastin and hyaluronic acid (HA).
- Collagen is vital to the overall health of the skin and improves the skin's elasticity, reduces wrinkles and increases the skin's moisture.
- Hyaluronic acid (HA) is a major component of the skin and is a naturally occurring substance found throughout the human body. HA works to neutralize free radicals, speed up healing and tissue repair; while revitalizing the skin’s outer surface layers. The HA molecule can hold a thousand times its weight in water; literally hydrating and plumping the skin for a fuller, softer and more youthful appearance.
- Elastin is the very stretchy protein found throughout the connective tissue and the skin. Elastin allows the tissues in the body to resume their shape after stretching or contracting. This vital protein plays a vital role to the structure of the skin and returns sagging skin to its original shape after it has been pulled, pinched or simply worn down over time.
RF [RADIO FREQUENCY]:
This unique deep-heating technology permeates deep into the layers of the skin;, encouraging cell turnover and the production of new collagen and elastin. RF technology works by rapidly changing electric field polarity- which alternately attracts and repels electrons and charged ions in the dermis and subcutaneous tissue.
- The tissue’s natural resistance to this process produces heat; and the thermal effect on the dermis leads to collagen stimulation and activation of fibroblast cells.
- Throughout this process, no current flows through the epidermis; therefore, the skin's surface is not exposed to heat so no additional superficial cooling is required.
- Over time, as the contraction and tightening of the tissues increases, the newly activated cells become trained and automatically begin to produce more collagen.
BENEFITS OF RF (RADIO FREQUENCY):
- Can be highly effective for the improvement of skin laxity, facial contours, fine lines and wrinkles
- The result is an improvement in skin quality, firmness and tightness that you can see and feel.
- RF opens the skin's pores to allow maximum absorption of nutrients from skin care products.
- The Mini V Max provides superior product (lead-in) absorption and restores the skin's fascia layer.
- RF treatments can be administered in the comfort of your own home and provide an incredible alternative to surgical face lifts and other costly cosmetic procedures.
Works directly into the SMAS
Non-invasive temperature which stimulates deep into the skin to promote the regeneration of collagen
Provides professional grade ultrasound which is highly focused and only works on the intended treatment area.
- Always administer HIFU treatments properly, in accordance with the instructions and recommendations
- When HIFU is administered at the appropriate intensity level-- treatments will be painless.
NO RECOVERY OR DOWN-TIME:
The energy passes over the skin; therefore, treatments are very comfortable and (when used correctly) should not hurt.
- Due to different skin types and the levels of intensity that each individual prefers, the sensitivity to the treatments will vary.
- It is not uncommon for the skin to experience an adjustment period for a couple of days following a treatment,
- The initial treatments may cause the skin to be somewhat sensitive or tender afterwards; however this effect is minor and should not disrupt daily life.
1. It is very important to remember to ADD WATER (follow the instrument instructions) before using this device to avoid damage to the machine.
2. It is absolutely necessary to use a CONDUCTIVE MEDIUM (Conductive Gel) on the skin when using this instrument--as well as any other Ultrasonic + RF Device.
- Always remember to replenish (whichever medium you are using) accordingly throughout the treatment. The machine uses the medium to increase the conductivity of the Mechanical wave/RF.
- Conductive Medium Examples: Ultrasonic Gel/ RF Conductive Gel/ Nutritional Skin Care Products/ Lotion / KY Jelly (One of the most common ultrasound gel alternatives) Bio Oil/ Moisturizers & Creams/ Skin Gel / Aloe Vera/ Polypeptide Concentrate
- NOTE: You can use any type of conductive gel/medium that you prefer. (Conductive Medium is not included with this device)
3. Please consult with a qualified beauty professional for additional guidance pertaining to other parts of the body that are not listed as safe or "suitable for use"
BEFORE TREATMENT: Important
- Thoroughly clean and dry the face and neck. It is necessary to apply some type of medium to the treatment area prior to using the device.
- *Before using instrument, you should clean the skin that is to be treated so as to prevent dirt form entering the skin through the penetration of the ultrasonic wave.
- *Please take off all the metal objects on your body before operation so as to avoid unexpected condition and affect the curative effect.
- When using the regular speed and lifting method- the medium needs to be reapplied once it has been fully absorbed or begins to dry out.
- When in use, the cartridge needs to be close to the skin and the medium helps with conduction of the different waves/frequencies.
- First: clean the treatment area (Remove any make up and use a cleanser to clean the area)
- Connect the power line: Press the round button to turn on the machine. (There is large round button on each side and you can press any one of them to turn on the machine. If the light turns on then the machine is on. If you need to turn off the machine: press and hold the button for 1.5 seconds
- The depths and energy of the machine can be adjusted when the machine turns on: We suggest operating at 4.5mm for the face.
- The energy of the Mechanical Wave and RF has 3 levels: Low , Medium and High.
- The round button on the handle can adjust the power of the RF.
- The reverse button can adjust the power of the Mechanical Wave.
- To test the energy intensity: First pull the device in an upwards motion from the right lower jaw- and to the top of mouth in a stable, consistent speed.
- If you feel nothing: simply adjust the energy of Mechanical Wave and RF. It is completely normal to feel a little heat, tingling or soreness.
- The round button below will be the Operation button/ pause button. Once you Press the operation button: and you will have 30 seconds of automatic output.
- During the output: all of the buttons will be unavailable and the buzzer will sound once every second. If it doesn’t sound then it means it has the device has finished the 30 second output.
- If you need to pause during the period of output then press the pause button.
- The square push button can adjust the depth. The depths are 3.0mm/4.5mm respectively and the red line corresponds to the depth.
NOT RECOMMENDED TO USE ON:
- The orbital bone
- Upper eyelids
- The temple
- The Adam’s apple
- The bridge of the nose.
- The Energy must be adjusted slowly from Low to High to find the best intensity to suit you.
- Do not directly open the intensity all the way to the maximum intensity--doing so may damage the skin (scald).
INSTRUCTIONS FOR THE ACCEPTABLE TREATMENT AREAS:
- During operation, the cartridge cannot continue a repetitive motion in one area.
- The device must continue moving at a constant speed at all times.
- Individual preferences to the levels/degrees of intensity vary from person to person. It is best to adjust the initial intensity to the lowest setting until the skin becomes acclimated to higher settings.
- Certain areas of the face/jawline will be more sensitive than others; this is natural.
- During the operation you will feel a slight sensation of heat which is normal; however, If the intensity is too high, some users may feel a stinging sensation in sensitive areas.
- If this is the case, decrease the intensity to a more suitable level and slowly increase the intensity to a desirable level over time.
FACE: Face Lifting/ Wrinkle Removal:
Enhances the skin's moisture to remove wrinkles and fine lines, activates the production of collagen, tightens the skin, shrinks pores, firms skin, reshapes facial contours, creates a defined V-Face.
- First: start with the lowest intensity and work from the jawbone to the cheekbone.
- Next: proceed by working from the mouth to the ears (manipulating the device by using a lifting motion).
- The last step: is to move from the side of the nose along the cheek bone/muscle; lifting the skin upwards and back towards the temple.
- Users should operate the device in a back and forth motion (3-4 times) depending on the looseness of the skin.
Improves the condition of the skin around the eyes and works to remove fine lines, crows feet and dark circles.
NOTE: *The skin around the eyes is very tender; so please use the lowest level when working around the eyes.
- Start from the lowest intensity and move in a lifting motion from the cheekbone and around to the temple.
- Next move in a lifting motion from the outer corner of the eye and around to the hairline.
- *Always remember that the upper eyelid and orbital bone around the eyes are forbidden.
- Users can operate the device in a repeated motion back and forth (3-4 times) according to the looseness of the skin.
- Start from the lowest intensity and move from between the eyebrows and lift to up and around the hairline.
- Move in a lifting motion from the middle of the eyebrows to the temple and then upwards towards the hairline (from the bottom up).
- *We suggest avoiding the eyebrows.
- Users can operate the device in a repeated motion back and forth (3-4 times) according to the looseness of the skin.
NECK AREA: See precautions pertaining to the Neck area
Massages and lifts the skin only AROUND the neck thus removing neck wrinkles and double chin.
- We suggest starting from the button line of the neck and moving towards the clavicle (along the side of the neck) using a lifting motion upwards towards the jawbone.
- Next move from the double chin area to the sides of the throat.
- The throat area (in the center of the throat/ adam's apple) is forbidden.
- Next move from the double chin to the lymph gland area and around. Again-Always remember that the throat area is forbidden.
- Lastly, users can operate the device back and forth 3-4 times according to the skin's individual needs.
Under NO circumstances should this device ever be used on the CENTER of the THROAT.
The instrument can neither be placed in a damp area or around a water source; nor be exposed to direct sunshine.
For the best treatment effects of the instrument and to ensure a long service life, please use the appointed accessories provided by the originating factory.
The instrument cannot be close to the strong heat source, if so, it shall affect the service life and normal use of the instrument.
The medium, such as water, oil, etc. cannot leak into the instrument--and the instrument cannot be knocked, thrown or handle heavy falls. This will permanently damage the instrument.
TESTING THE ENERGY INTENSITY:
For best results, and depending on your level of sensitivity we recommended:
- 3.0mm: suitable for the forehead and around the eyes
- 4.5mm: suitable for the face, jaw line, double chin and the skin around the neck
- First pull up from the right lower jaw to the top of mouth in a constant/stable speed. If you feel nothing then you can adjust the energy of the Mechanical Wave and RF accordingly. It is normal to feel heat, tingling or slightly sore.
- When operating around the wing of the nose the energy needs to be lowered.
- Different treatment areas can bear different levels of energy. You will need to adjust the energy according to individual tolerance.
- Treatment Time: It should take approximately 30-45 minutes for a complete operation to the entire face
TREATMENT INSTRUCTIONS FOR SPECIFIC SKIN TYPES:
- For the the first 5 initial uses- we suggest 1 treatment every 3 days. After the fifth treatment- we recommend 1 treatment every 5 days.
- For the first time using Mechanical wave and RF: you will need to start from the lowest intensity.
- You can adjust the intensity according to individual preference and/or the maximum tolerance level during the treatment.
- For the first 5 uses we suggest 1 treatment every 5-7 days.
- After the fifth complete treatment we recommend 1 treatment every 10-15 days.
- You can eventually design your individual treatment schedule according to the needs of the skin.
- For the first use: we suggest only turning on the Mechanical wave. After using the device 3-4 times- you can turn on the RF with the Mechanical Wave at the same time.
- For RF energy: start from the lowest intensity and adjust the power of Mechanical Wave according based on your maximum tolerance.
SENSITIVE/ CUTICLE SLANTS/ THIN SKIN:
- For the fist use: we suggest starting with the Lowest power of Mechanical Wave and RF.
- After using 2-3 times, you can adjust the energy to your maximum tolerance (according to individual/personal skin situation).
During the treatment:
- It is NECESSARY to apply some type of medium (conductive medium/cream/gel) on the treatment area.
- The cartridge needs to closed to the skin and operated at a regular/constant speed while using a lifting method. The medium needs to be resupplied when it has absorbed or become dried.
- A complete treatment: usually takes 30-45 minutes for one complete operation to the entire face. (The operating time may change according to the size of face).
- Cleaning the cartridge with damp or slightly wet towel is necessary after the operation has completed.
- You must clean the cartridge with a wet towel is immediately after the treatment in order to keep the device protected.
After the operation:
- Clean the face with warm water or clear water (hot water not suggested).
- Apply a moisturizing mask immediately after the operation and leave the mask on for about 10-15 minutes.
Note: For parts that are not listed as safe: please consult a professional beauty specialists for help/guidance.
- After using the device, it is normal for the skin to feel slightly sore or a little swollen.
- Rinse the face with warm tepid water (water that is too hot may irritate the skin) following the treatment to remove the medium from the face.
- Pat the skin dry and apply a hydrating mask to soothe the skin.
After operating the device you may have varying degree’s of Metabolism Detoxification (possibly resulting in pimples, acne, small lumps, flushed skin, light edema, soreness, or slightly itchy skin) This is a normal situation and the skin will usually will recover naturally within 1-3 days. Some special cases may need more time for recovery. If this happens, apply more moisturizing masks to re-hydrate the skin. Each of these cases are a normal and temporary reaction to the treatment.
*Women are not allowed to operate this product during physiological periods.
*For those whose skin is experiencing allergies/allergic: it is recommended to only use this product one week after the allergy has ended.
If you have had hyaluronic acid or any other kind of cosmetic injections into the skin, it is recommended wait to use this product 30 days after treatments have passed before using this device.
*Areas of the body that have silicon implants should not be treated.
*Not recommended for use on sites with vulnus or large-scale acne or pustules. *Patients who suffer from serious diseases, heart disease, psychiatric and so on are not to use this product.
*Not recommended for persons with serious skin disease, infectious disease or hormone imbalances.
*Women who are pregnant cannot use this device, Please wait one month after giving birth to use this device.
Not recommended for anyone with a pacemaker or wire implants of any kind (wire is not absorbable)
It is recommended that you apply a moisturizing mask at least 3-4 times a week, and drink not less than 2000cc (eight glasses of water) a day following use.
1* beauty machine
1* power adapter
1* gift box
1* water injection tool
NOT INCLUDED: *The package does not include ultrasonic conductive gel.
ESTIMATED SHIPPING TIME: 19-24 days
Manufacturing Process: Machine Made
Power Source: Rechargeable Battery
Function: Skin Rejuvenation
Function: Skin Tightening
Material: ABS and Metal